Acer Aspire E5-771G Intel SATA AHCI Driver
Драйвера для Acer Aspire Z для Windows 7 x 64 Все Комплект драйверов для ACER Aspire EG. Intel SATA AHCI Driver. Intel SATA AHCI Driver for Acer Aspire VG (Acer VG) v Aspire E; Aspire EG; Aspire V; Aspire V; Aspire V Description of problem: On laptop Acer E 17 (EGSL) gives xrandr on 04) f.2 SATA controller: Intel Corporation 8 Series SATA Controller 1 [AHCI.
|Supported systems:||ALL Windows 32x/64x|
|Price:||Free* [*Free Registration Required]|
Acer Aspire E5-771G Intel SATA AHCI Driver
Here, the photo shows the clips for Module 1 already partly pushed aside. The module would then pop up. To add another module instead of removing one, I would just push it into the empty socket shown here as Socket for Module 2 and then push it down until its clips Clips for Module 2 held it in place.
When I did add the third module, later, I had to play around for a while before I figured out how to get it to go in all the way. Installing two hard drives meant removing the mounting bracket also called a caddy or a tray from the stock drive and installing it onto the SSD, and also getting a second bracket for the replacement hard drive.
The bracket is the light-colored piece of metal shown in the drive bay at the bottom left of the photo above.
ACER Aspire E5-771G Intel SATA AHCI driver download free (ver. 18.104.22.1686)
I had not realized that it would be necessary to buy a mounting bracket. It was hard to find one. The part number stamped onto the existing bracket was Acer Aspire E5-771G Intel SATA AHCI Those are zeroes, not ohs. A search turned up very few references to it. I eventually found it: This was not a situation calculated to inspire love of Acer.
Drivers and utilities for Notebooks / Laptops (Netbooks) Acer:
Designing a substitute would not be easy: It looked like a bracket for an Acer Aspire G might also fit. I sent them an email asking if they had a caddy for a G. They eventually pointed me to exactly the right item in their product list.
But by that point, I had worked out my own solution. First, I decided to use the existing caddy for the replacement hard drive, since unlike the SSD it had exposed circuits that might come afoul of whatever Acer Aspire E5-771G Intel SATA AHCI clips or pieces of rubber I might shove into the bay to support it in lieu of a genuine mounting bracket. I swapped the bracket from the stock drive to the replacement drive, put the replacement HDD into drive bay 2, and focused my attention Acer Aspire E5-771G Intel SATA AHCI the SSD and drive bay 1.
One possibility was to use tin snips to cut up a soup can and bend the resulting pieces into four appropriately sized and shaped brackets, one for each corner of the SSD. I reasoned that it might not be necessary to have the two tongues that screws would affix to the case see photo, above if I could instead design springy brackets that would push up, down, and sideways at the opposite end of the SSD.
This sounded like a lot of work Acer Aspire E5-771G Intel SATA AHCI perhaps several sliced fingers from the sharp edges of the tin, however, and anyway I figured most people do not have tin snips and therefore my solution would be unhelpful though some kinds of ordinary scissors might also be sacrificed to the mission. I noticed that the drive bay and the inside of the back panel came with pieces of foam and solid rubber installed.
I guessed that drive temperatures probably would not be so hot as to melt those pieces. So it seemed that I might use rubber to keep the SSD in place upwards and downwards.
Drivers and utilites for Acer Notebooks / Laptops and Netbooks - choice of model.
The SSD came with a sort of rubber gasket; it looked to be about the right thickness to cushion between the SSD and the back panel. I put the gasket in place.
Turning to the opposite side of the SSD in this case, the side with the Kingston labelI found that I had a thick piece of double-stick foam. Not quite thick enough. I fortified it with a layer of double-stick tape. I also put some double-stick tape onto Acer Aspire E5-771G Intel SATA AHCI preexisting foam cushions near the connector end of the bay. I left the protective tape in place on the top layer of double-stick foam; no need to permanently secure the SSD into the bay.
This three-point contact arrangement was not ideal, but with Acer Aspire E5-771G Intel SATA AHCI length of the SATA connectors, it seemed unlikely that there would be twisting forces sufficient to cause damage. There remained the need to exert lateral pressure from the non-connector end of the SSD.